Oracle Secure Backup provides the ability to perform automatic tape drive cleaning as well as the option to manually clean a tape drive. The following article provides a brief overview of the tape cleaning functionality built into OSB.
After importing a cleaning cartridge to the tape library, you need to inform OSB that the media just inserted is not a data volume but rather a cleaning tape. Inserting a cleaning cartridge and performing an inventory through OSB while not indicating to OSB that a cleaning cartridge was inserted will result in OSB thinking the new media is a normal data tape. If you were to attempt a tape cleaning operation, the following errors would occur:
ob> clean --drive tape1 --force --use 8
Error: can't execute command - specified element does not hold a cleaning tape
ob> clean --drive tape1 --force
Error: can't execute command - could not find a usable cleaning tape
Import the cleaning cartridge into a vacant storage element (i.e. storage element 8). Next, notify OSB of the newly imported cleaning cartridge, using the insertvol command. In my example, I already used the cleaning tape once on another drive so I indicate --uses 1
ob> insertvol --library lib1 clean --uses 1 --maxuses 15 8
Manually Cleaning a Tape Drive
Use the clean command in obtool to request a manual cleaning be performed on the selected tape drive. The --force option will force the tape to be cleaned. If there is a tape loaded in the tape drive, then selecting this option unloads the tape, loads the cleaning tape, cleans the tape drive, and then reloads the tape that was originally in the tape drive.Import the cleaning cartridge into a vacant storage element (i.e. storage element 8). In my example, I already used the cleaning tape once on another drive so I indicate --uses 1
ob> insertvol --library lib1 clean --uses 1 --maxuses 15 8
ob> lsvol --library lib1
Inventory of library lib1:
in 1: volume RMAN-TESTDB1-MF-000006, 83909632 kb remaining, content manages reuse
in 2: volume RMAN-TESTDB1-MF-000004, 87050240 kb remaining, content manages reuse
in 3: occupied
in 4: occupied
in 5: occupied
in 6: occupied
in 7: occupied
in 8: cleaning tape: 1 use, 14 remaining
ob> clean --drive tape1 --force --use 8
ob> lsvol --library lib1
Inventory of library lib1:
in 1: volume RMAN-TESTDB1-MF-000006, 83909632 kb remaining, content manages reuse
in 2: volume RMAN-TESTDB1-MF-000004, 87050240 kb remaining, content manages reuse
in 3: occupied
in 4: occupied
in 5: occupied
in 6: occupied
in 7: occupied
Configuring Automatic Tape Drive Cleaning
Oracle Secure Backup allows you to configure a tape library to automatically perform a type drive cleaning whenever a tape drive reports that it needs cleaning or when a specified usage time has elapsed.Use the --autoclean option of the mkdev or chdev commands of obtool to configure the library to perform automatic cleaning. When the autoclean option is set to yes, the cleaning cycle is initiated either when a tape drive reports that it needs cleaning or when a specified usage time has elapsed. Oracle Secure Backup checks for cleaning requirements when a cartridge is either loaded into or unloaded from a tape drive. If at that time a cleaning is required, then Oracle Secure Backup performs the following steps:
- Loads a cleaning cartridge
- Waits for the cleaning cycle to complete
- Replaces the cleaning cartridge in its original storage element
- Continues with the requested load or unload
The following example queries the tape library configuration for lib1. As you can see, the autoclean option is not currently set:
To enable automatic tape drive cleaning, use the chdev option:ob> lsdev --type library --long lib1
lib1:
Device type: library
Model: [none]
Serial number: [none]
In service: yes
Debug mode: no
Barcode reader: default (hardware-selected)
Barcodes required: no
Auto clean: no
Clean interval: (not set)
Clean using emptiest: no
Ejection type: auto
Min writable volumes: 0
UUID: 89064982-0df2-102c-8f89-00146cc1a7c7
Attachment 1:
Host: packmule
Raw device: /dev/sg0Another query on the tape library device shows that auto-cleaning is enabled:ob> chdev --type library --autoclean yes --cleanemptiest no lib1
In addition to simply enabling auto-cleaning, OSB allows you to specify two other options:ob> lsdev --type library --long lib1
lib1:
Device type: library
Model: [none]
Serial number: [none]
In service: yes
Debug mode: no
Barcode reader: default (hardware-selected)
Barcodes required: no
Auto clean: yes
Clean interval: (not set)
Clean using emptiest: no
Ejection type: auto
Min writable volumes: 0
UUID: 89064982-0df2-102c-8f89-00146cc1a7c7
Attachment 1:
Host: packmule
Raw device: /dev/sg0
--cleanemptiest/-E {yes | no}
Specifies which cleaning tape to use. This option is useful when a tape library contains multiple cleaning tapes. The default value of yes specifies the emptiest cleaning tape, which causes cleaning tapes to round robin as cleanings are required. The no value specifies that obtool should use the least used cleaning tape, which uses each cleaning tape until it is exhausted, then uses the next cleaning tape until it is exhausted, and so forth.--cleaninterval/-i {duration | off}
Specifies whether there should be a cleaning interval, and if so, the duration of the interval. The default is off. The duration is the interval of time a tape drive is used before a cleaning cycle begins. If automatic tape drive cleaning is enabled, then duration indicates the interval between cleaning cycles. For tape drives that do not report cleaning requirements, you can specify a cleaning interval, for example, 30days.
in 8: cleaning tape: 2 uses, 13 remaining
No comments:
Post a Comment